Gbc laminator service manual

The assembly number and the model number can be found on a white sticker on the center of the bottom. This device has a photo quality laminaton, and also has a 9" throat opening that is compatible with pouches that are 3mil and 5mil thick.

This laminator includes two 5-pack self adhesive glossy pouches. The device laminates documents at a fixed speed of 10" per minute.

As an old model, one might face several common problems with this device. Some common problems include carrier sheets getting stuck to the laminator, overheating, and broken gears. GBC web page. EZ Lam Operators Manual k. EZ Lam 2 Operators Manual k. Finisher Operators Manual k. Ibico Kombo Assembly Instructions k. Lamitek Photosmart Instruction Manual 1, k. MightyLam Manual 2, k. OD Manual 2, k.

Personal VeloBinder Manual k. SR90 Bookletmaker Manual 2, k. Titan Coil Binding Manual k. ValueLam Manual k. Jun-Air Compressor Operators Manual 2, k. Money Handling. Cassida Counterfeit Detector k. Cassida Counterfeit Detector 3, k. Cassida Counterfeit Detector 4, k. Cassida Bill Counter 6, k. Cassida C Coin Counter 6, k. Cassida Concepta Bill Counter 9, k. Pouch Laminating Machines. ML 6 Instruction Manual k.

ML13 Pouch Laminator k. Harsh chemicals like toluene, acetone or MEK destroy the silicone covering of the rolls. Raise the upper main roll when the laminator is not in operation.

Prolonged contact can damage the rolls. Excess pressure can damage the laminating rolls. Always select the minimum roll pressure necessary to complete the task. It can harden within an hour and ruin the roll. The operating environment must be free of dust, flammable liquids and vapors.

You can be injured by inhaling chemical vapors. Vapor build up or stored flammable liquids can cause a fire. Excessive dust can damage the laminator. Do not use a knife or other sharp instrument during installation or while servicing the laminator. You can cause irreparable damage to the rolls. Do not attempt to move the laminator across anything other than a flat, level surface without trained and qualified riggers.

You can be crushed or seriously injured. The F Laminator is a large and heavy piece of equipment. GBC Pro-Tech bears no responsibility for personal injury or damage due to moving the laminator improperly. Do not operate the laminator if the power cord is damaged or frayed. Contact a qualified electrician to replace the cord. Do not allow anything to rest on the power cord. Do not locate the cord where people can walk on it.

You or others can be severely shocked, electrocuted or cause a fire. Always use good safety practices when operating or servicing the laminator and know how to react quickly in an emergency. Posted at various locations on your F Laminator are important safety labels.

Figure shows the location of each of these labels. Read and understand the Operation Manual and all safety labels before operating this machine. Only a trained person is to be permitted to operate this machine.

Training should include instruction in operation under normal conditions and emergency situations. This machine is to be serviced only by trained and authorized personnel. Follow lockout procedures before servicing. Never leave the machine stopped in such a manner that another worker can start the machine while you are working on or within the machine. Never change or defeat the function of electrical interlocks or other machine "shutdown" switches.

Before starting this machine, check that:. There is a potential hazard of entanglement in this machine caused by items such as long hair, loose clothing, and jewelry.

Make sure your clothing and hair fit closely to your body and that all jewelry, rings and watches are removed. Air pressure must be less than PSI kPa to avoid damaging the machine. Press this button to stop the machine cycle, remove electric power, and separate open rolls to eliminate a pinch point on some machines. GBC Pro-Tech is committed to a program of ongoing product improvement. As a result, we are providing these instructions so that you can insure that your new F Laminator is properly and securely unpacked, moved and installed.

Before a F Laminator can be installed, there are a few requirements that must be met. Make certain that each of the requirements listed in the following preinstallation checklist are met before beginning installation. Failure to follow the preinstallation checklist can result in damage to the laminator. Are doorways and hallways wide enough for the laminator to be moved to the installation site?

A work area must be established that allows for operation in both the front and the rear of the machine and provides space for efficient material flow. Figure shows a typical machine area layout. Is the environment appropriate for the laminator? However, the laminator must not be located where there is air blowing directly on it. Major fluctuation in temperature and humidity are to be avoided.